注塑常用术语英文表达.doc

1.雾气 Moisture Streaks
2。玻纤分配不均 Glass Fiber Streaks
3。困气 Gas Trap Effect
4.银丝纹 Sliver Marks
5.结合线 Weld Line
6。水波痕 Water Wave Effect
7.黑点 Dark Sport
8.顶出印 Visible Ejector Marks
9.变形 Deformation During Demolding
10。填充不足 Short Filling
11。冷料流痕 Cold Slug
12.进胶口点不良 Dull Spots Near The Sprue
13。喷射痕 Jetting
14.表面起层 Flaking Of The Surface Layer
15。浮泡 Entrapped Air
16。过热变色 Burnt Streaks
17.龟裂 Stress Crack
18.缩水痕 Sink Marks
19。真空气泡 Density Bubble
20.披锋 Flash
21。擦伤印 Scratch MarksGlass fiber rich surface/glass emergence on the surface
22 尺寸过大 Over dimension
23尺寸过小 Under dimension
24 翘曲 Warpage/warped
25 收缩 Shrinkage/shrink
26 缩影 Sink marks
27 打不满 Short shot/short molding
塑料模具mould of plastics
注塑模具injection mould
冲压模具die
模架mould base
定模座板Top clamping plate
Top plate
Fixed clamp plate
水口推板stripper plate
A板A plate
B板B plate
支承板 support plate
方铁 spacer plate
底针板 ejector plate
面针板 ejector retainer plate
回针 Return pin
导柱 Guide pin
有托导套 Shoulder Guide bush
直导套 Straight Guide bush
动模座板Bottom clamp plate
Moving clamp plate
基准线datum line
基准面datum plan
型芯固定板core-retainer plate
凸模固定板punch—retainer plate
顶针ejector pin
单腔模具single cavity mould
多腔模具multi-cavity mould
多浇口multi—gating
浇口gate
缺料starving
排气breathing
光泽gloss
合模力mould clamping force
锁模力mould locking force
挤出extrusion
开裂crack
循环时间cycle time
老化aging
螺杆screw
麻点pit
嵌件insert
活动镶件movable insert
起垩chalking
浇注系统feed system
主流道 sprue
分流道runner
浇口gate
直浇口direct gate , sprue gate
轮辐浇口spoke gate , spider gate
点浇口pin—point gate
测浇口edge gate
潜伏浇口submarine gate , tunnel gate
料穴cold-slug well
浇口套sprue bush
流道板runner plate
排飞槽vent
分型线（面）parting line
定模stationary mould，Fixed mould
动模movable mould, movable half
上模upper mould， upper half
下模lower mould， lower half
型腔cavity
凹模cavity plate，cavity block
拼块split
定位销dowel
定位销孔dowel hole
型芯core
斜销angle pin, finger cam
滑块slide
滑块导板slide guide strip
楔紧块heel block, wedge lock
拉料杆sprue puller
定位环locating ring
冷却通cooling channel
脱模斜度draft
滑动型芯slide core
螺纹型芯threaded core
热流道模具hot-runner mould
绝热流道模insulated runner mould
熔合纹weld line （flow line）
三板式模具three plate mould
脱模ejection
换模腔模具 interchangeable cavity mould
脱模剂release agent
注射能力shot capacity
注射速率injection rate
注射压力injection pressure
差色剂colorant
保压时间holdup time
闭模时间closing time
定型装置sizing system
阴模female mould，cavity block
阳模male mould
电加工设备Electron Discharge Machining
数控加工中心CNC machine center
万能铁床Universal milling machine
卧式刨床Horizontal planer
车床Engine lathe
平面磨床Surface grinding machine
去磁机Demagnetization machine
万能摇臂钻床Universal radial movable driller
立式钻床Vertical driller
超声波清洗机Ultrasonic clearing machine