装修专项施工方案.doc
《装修专项施工方案.doc》由会员分享,可在线阅读,更多相关《装修专项施工方案.doc(39页珍藏版)》请在咨信网上搜索。
1、深圳海外装饰工程有限公司SHENZHEN OVERSEAS DECORATION ENGINEERING CO. LtdConstruction Plan施工方案Construction Plan施工方案Section 1.0 Plasterboard Partition on Metal Stud第一节 轻钢龙骨隔断施工方案1.1 Requirement of Materials, Components and Fittings材料及构配件要求 Each kind of stud, fittings and surface materials should accord with the c
2、urrent requirement. Re-testing will be conducted when more than 500 square meters man-made boards are used. Provide test report of TVOC and formaldehyde for water-based adhesive.各类龙骨,配件和罩面材料及胶粘剂的材质应符合现行要求.人造板材使用量大于500平米时应进行复检;水性胶粘剂必须有TVOC和甲醛检测报告。 Filled with insulation material: The glass wool, rock
3、 wool, etc。 should be consistent with the design requirements填充隔音材料:玻璃棉,岩棉等应符合设计要求。1。2 Main Equipment and Tools主要机具 Electrical machine & tools: Electrical saw, Hand-held electric drill, impacting drill, DC welding machine, and cutting machine电动机具:电锯,手电钻,冲击电钻,直流电焊机,切割机。 Manual tool: manual saw, plier
4、s, riveter, screwdriver, level and steel level手动工具:手锯,钳子,拉铆钳,螺丝刀,靠尺,钢水平尺.1.3 Metal Stud Installation龙骨安装The type, size, color of the materials and the structure fixing method of the partition should comply with the design. 隔断工程应用材料的品种、规格、颜色以及隔断的构造固定方法应符合设 计要求.As per the drawings, setting lines on th
5、e cleaned floor for the wall locating and drawing out the locations of doors, windows and preformed openings。按图纸要求,在清洁干净的地面上放墙位线定位,并标出门、窗及预留孔位置,确定墙体位置Install the top and bottom studs at the wall location, screws shall be used to fix the studs and the space between screws is 600mm.在墙体位置上安装沿地、沿顶龙骨,固定龙
6、骨采用螺钉固定,螺钉间距为600mm。The vertical studs will be installed into the top and bottom studs, adjusting the dimensions and verticality, the vertical studs by the walls will be fixed by screw every 800mm and the other vertical studs by rivets。 When the studs located at doors, windows and the preformed openi
7、ngs, additional studs will be added and to be fixed by rivets.竖向龙骨的上、下两端插入沿地、顶龙骨,按要求调整尺寸,放垂直,靠墙两边的竖龙骨,用螺钉将其固定,钉距800mm,其它龙骨采用抽心铆钉固定.但当龙骨位置在门口、窗口或其他预留孔时,主要加撑并用铆钉固定.1。4 Gypsum Board 石膏板安装 Installation安装The gypsum board should be installed in vertical and the sealed edge of the board should be parallel
8、with the vertical metal stud。 25mm screws should be installed to firm the gypsum boards on metal stud along the centerline of the vertical stud flange将石膏板边(有封口的一边)与竖向龙骨平行.对准竖向龙骨翼缘的中心线上,用25mm螺钉固定。The self-tapping screw to the edge of boards should be within 10 to 16 mm. The center screws will be ever
9、y 300mm and the surround screws 200 mm 自攻螺钉与石膏板边缘距离不得小于10mm,也不得大于16mm.螺钉固定位置中距为300mm,周边间距为200mm.When fixing the boards, the work should be done from the middle to the long and short edges; after screw drove in, the heads should be slightly submerged into the board but not more than 1。5 mm broken the
10、 face paper. 固定板时,应从一块板的中部向长边及短边固定,螺钉就位后,钉头略埋入板内。埋入深度不大于1.5mm,并不能破坏纸面。The joints of gypsum boards should be tight, but not press them into the position。石膏板对接时应靠紧,但不能强压就位.The joints of the boards should be staggered and the both sides board joints should not be on the same studs.墙面对接缝应错开,墙两面的接缝不能落在同一
11、条竖龙骨上.The external corner of gypsum boards should be metal protected。石膏板墙阳角须使用金属护角包角。 Treatment and Making up of the Joints处理接缝The concave area at the gypsum board joints should be caulked by special sticky paste through wide putty knife。在石膏板对接所形成的接缝用宽刮刀均匀地添上专用粘接剂粘接。Plastering the centerline of punc
12、hed paper tape align with joints, squeezing the sticky paste into the holes by wide scraper。 Removing all the residual paste and the air holes under the paper tape, the scraper will be 45 degrees to the wall。 Sufficient sticky paste should be squeezed in to ensure the strength of the joints.将穿孔纸带的中线
13、对准接缝,用宽刮刀按入接缝粘固粉。用刮刀顺着接缝刮去多余的粘固粉并除去纸带下的气泡,刮刀应与接缝约成45度角.纸带下应留有足够的粘固粉,以使接缝 粘合牢固.Scraping very thin sticky paste on the paper tape avoiding the tape crinkling and cracking. The dry out will be waiting (normally for one hour).立即刮上薄薄一层粘固粉。这可以防止纸带的边卷起或起皱,以免裂开。等待干燥(在正常条件下需要1小时)。After drying out, plaster th
14、e second layer of sticky paste 150mm wider than the first and waiting for it drying out. 燥后用抹刀再抹上第二层接缝粘固粉,比第一层宽150mm,等其干燥。When the second sticky grease dried out, coating again the third layer of sticky paste at least 50 mm wider than the secondary layer。 The residual paste should be removed and fin
15、ish the surface smoothly。等第二层干燥后,用抹刀再抹上一层粘固粉,应比前一层至少宽50mm。刮去接缝上多余的粘固粉,使表面平整光滑。After the sticky paste totally dried out, 150 sandpaper will be used to finish the joints smoothly。完全干燥后,用砂纸板与接缝成对角轻轻打磨,以使表面平滑。应使用150号砂纸。In order to obtain the optical plane face, the joints should avoid。 If inevitable, th
16、e method same as concave edge joints will be used to jointing on the studs, but special sticky grease should be increased to 600 mm wide. As the wider sticky grease will be good for smoothing the finished surface.为了取得最佳整修平面,应尽量避免对接缝。如果无法避免,可采用与凹陷边缘接缝相同的方式在龙骨框上进行对接,但是盖缝粘固粉需加宽到600mm.加宽的盖缝粘固粉有助于取得平整光滑的
17、表面。For inner corners, plastering sticky paste on corner sides, the middle folded paper tapes are put into corners by scraper or angled tools. When total dry, plastering again and being sure this layer is wider than the first. Sandpaper finishing must be done when it dried totally内角的处理。用宽刮刀在墙角的两边刮上粘固
18、粉。将纸带沿中心线折起,然后用刮刀或角度工具按入粘固粉。完全干燥一再刮上一层粘固粉,确保边缘宽于前一层.完全干燥后用砂纸轻轻打磨。For external corners, plastering sticky pastes onto the metal protective corner sides and squeeze paste into the holes。 When total dry, second plaster should be done and the second be wider than the first. Sandpaper finishing is done w
19、hen it dried totally。 外角的处理。用宽刮刀在钉在墙角上的护角两边刮上粘固粉,刮时用力将粘粉压入护角的孔眼。干燥后再用平抹刀刮上一层粘固粉,边缘应宽于前一层。完全干燥后用砂纸轻轻打磨。Treatment to screw holes, plaster 3 times sticky paste on the holes, the way is same as that for joints。 Every plaster should be 25 mm wider than the former one。 When dried out, sand paper work ligh
20、tly.螺丝孔钉的处理.在螺丝孔上刮上三层粘固粉,方法与接缝相同。每层粘固粉应宽于前一层25mm。完全干燥后用砂纸轻轻打磨.The decoration work could be done directly on the gypsum board when the joint treatment finished.接缝处理完毕之后可以直接在石膏板表面进行装饰。 Quality Requirement质量要求Finished gypsum board wall should be plane, vertical, neat and without any deformation。完成后的石膏板
21、表面应表面平整、立面垂直、无翘曲、观感洁净.The gaps of the boards should be even and smooth.在板与板之间的接缝抹灰处应宽窄一致、平直光滑。The light steel joist must be strong, plane and straight, with sufficient bearing capacity. 轻钢龙骨架必须坚固平直,并有足够的承载能力。Section 2。0 Metal Ceiling Tile 第二节 金属板吊顶施工方案2。1 Construction Preparation 施工准备Drawing review
22、and construction plan working out ; Make site measurement and make layout of main joist and installation scheme according to the siite situation as well as make arrangement for Airconditioning ventilation opening, manhole, and lighting opening. Work out work sequence, detail drawing and perform real
23、 technical requirement & intention explanation。审核图纸进行实地丈量,并按实际情况,制定施工方案:绘制主龙骨走向及布置图,制定空调排风孔、检查孔、照明孔安装方案,制定施工顺序及节点详图,进行技术交底。Contact and coordinate with relative trade team at the location of ceiling fitting and preinstall hangers or embedded parts during main structure construction and confer with li
24、ghting, HVAC trade team on the working procedure arrangement。 在进行吊顶的部位,与有关工种联系配合,在主体结构施工时,预留吊杆或埋件,与照明、通风专业协商好工序插入时间。Construction equipment should be ready for construction completely。 Main construction machine includes: profile cutting machine, pistol drill, impact drill, level, angle square, powder
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 装修 专项 施工 方案
1、咨信平台为文档C2C交易模式,即用户上传的文档直接被用户下载,收益归上传人(含作者)所有;本站仅是提供信息存储空间和展示预览,仅对用户上传内容的表现方式做保护处理,对上载内容不做任何修改或编辑。所展示的作品文档包括内容和图片全部来源于网络用户和作者上传投稿,我们不确定上传用户享有完全著作权,根据《信息网络传播权保护条例》,如果侵犯了您的版权、权益或隐私,请联系我们,核实后会尽快下架及时删除,并可随时和客服了解处理情况,尊重保护知识产权我们共同努力。
2、文档的总页数、文档格式和文档大小以系统显示为准(内容中显示的页数不一定正确),网站客服只以系统显示的页数、文件格式、文档大小作为仲裁依据,平台无法对文档的真实性、完整性、权威性、准确性、专业性及其观点立场做任何保证或承诺,下载前须认真查看,确认无误后再购买,务必慎重购买;若有违法违纪将进行移交司法处理,若涉侵权平台将进行基本处罚并下架。
3、本站所有内容均由用户上传,付费前请自行鉴别,如您付费,意味着您已接受本站规则且自行承担风险,本站不进行额外附加服务,虚拟产品一经售出概不退款(未进行购买下载可退充值款),文档一经付费(服务费)、不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
4、如你看到网页展示的文档有www.zixin.com.cn水印,是因预览和防盗链等技术需要对页面进行转换压缩成图而已,我们并不对上传的文档进行任何编辑或修改,文档下载后都不会有水印标识(原文档上传前个别存留的除外),下载后原文更清晰;试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓;PPT和DOC文档可被视为“模板”,允许上传人保留章节、目录结构的情况下删减部份的内容;PDF文档不管是原文档转换或图片扫描而得,本站不作要求视为允许,下载前自行私信或留言给上传者【天****】。
5、本文档所展示的图片、画像、字体、音乐的版权可能需版权方额外授权,请谨慎使用;网站提供的党政主题相关内容(国旗、国徽、党徽--等)目的在于配合国家政策宣传,仅限个人学习分享使用,禁止用于任何广告和商用目的。
6、文档遇到问题,请及时私信或留言给本站上传会员【天****】,需本站解决可联系【 微信客服】、【 QQ客服】,若有其他问题请点击或扫码反馈【 服务填表】;文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“【 版权申诉】”(推荐),意见反馈和侵权处理邮箱:1219186828@qq.com;也可以拔打客服电话:4008-655-100;投诉/维权电话:4009-655-100。