压力容器工程规范(中英文对照).docx
《压力容器工程规范(中英文对照).docx》由会员分享,可在线阅读,更多相关《压力容器工程规范(中英文对照).docx(38页珍藏版)》请在咨信网上搜索。
1、压力容器工程规定Engineering Specification for Pressure VesselsC O N T E N T S目录1. GENERAL 概述1.1 Scope 范围1.2 Codes, Standards and Regulations 规范、标准及规章 1.3 Units 单位1.4 Purchasers Drawing and Documents 买方图纸及文件1.5 Vendors Drawings and Documents 卖方图纸及文件1.6 Site Condition 现场条件2. DESIGN 设计2.1 Design Pressure 设计压力2
2、.2 Design Temperature 设计温度2.3 Corrosion Allowances 腐蚀余度2.4 Materials 材料2.5 Loading Conditions and Strength Calculation 负荷条件及强度计算2.6 Tolerances 允许偏差3. DETAIL DESIGN 详细设计3.1 Shells and Heads 容器壁及顶3.2 Internals 内件3.3 Nozzles and Manholes 设备口及人孔3.4 Bolts, Nuts and Gaskets 螺栓、螺母及垫片3.5 Supports 支架3.6 Misc
3、ellaneous 其它4. FABRICATION 制作4.1 Plate Layout 排板4.2 Forming 成型4.3 Welding 焊接4.4 Heat Treatment 热处理5. INSPECTION AND TESTS 检测及试验6. NAMEPLATE, PAINTING AND MARKING 铭牌、刷漆及标识6.1 Nameplate 铭牌6.2 Painting 刷漆6.3 Marking 标识7. PACKING AND SHIPPING 包装和运输7.1 General 概述7.2 Packing and Preparation for Shipping 包
4、装与运输准备7.3 Shipping 运输Appendix A: Tolerance for Pressure Vessels 附A:压力容器允许偏差1. GENERAL1.1 Scope1.1.1 This specification together with the engineering drawings covers the requirements for the materials, design, fabrication, inspection, testing and supply of pressure vessels used for *project *本规范及工程图纸
5、包含对*工程中使用的压力容器的材料、设计、制作、检测、试验及供应的要求。This specification shall be referred to also for the non-pressure vessels except for the requirements of local regulation if vessel shape is similar to pressure vessels.本规范也可用于外形与压力容器相同的非压力容器。1.1.2 The definition of pressure vessels shall be in accordance with “Th
6、e Pressure Vessels Safety Technology Supervision Procedures” in the Peoples Republic of China.压力容器的限定根据中国的“压力容器安全技术监督程序”进行。1.1.3 This specification does not apply, in general, to auxiliary pressure vessels which are attached to turbines, engines, pumps, compressors and other mechanical equipment whi
7、ch are normally designed under the manufacturers standard.一般情况下,本规范不适用于涡轮、发动机、泵、压缩机及其它依照厂家标准设计制造的机械设备的附属压力容器。1.2 Codes, Standards and Regulations 规范、标准及规章1.2.1 Pressure vessels fabricated in China shall be designed, fabricated, inspected and tested in accordance with the requirements of the followin
8、g codes, standards and regulations of the latest edition.中国制作的压力容器必须根据以下最新版的规范、标准及规章的要求进行设计、制作、检测及试验。(1) The Pressure Vessels Safety Technology Supervision Procedures (1999 edition)压力容器安全技术监督程序(1999年版)(2) Steel Pressure Vessels GB1501998 钢制压力容器(3) Technical Specification for Fabrication of Steel Che
9、mical Vessels HG20584-1998钢制压力容器制作技术规范(4) Steel Welded Atmospheric Pressure Vessels JB/T47351997 钢制焊接常压容器(5) Basic Specification for Steel Chemical Vessel Design HG20580-1998 钢制化学容器设计基本规范(6) Specification for Materials Selection of Steel Chemical Vessels HG20581-1998钢制化学容器材料选择规范(7) Specification for
10、 Stress Calculation of Steel Chemical Vessel HG20582-1998钢制化学容器强度计算规范(8) Specification for Structural Design of Steel Chemical Vessel HG20583-1998 钢制化学容器结构设计规范(9) Technical Requirements for Fabrication of Steel Chemical Vessels HG20584-1998 钢制化学容器制作技术要求(10) Mechanical Agitation Equipment HG/T20569-9
11、4 机械搅拌设备(11) Mechanic Properties Test of Welding Specimen for Steel Pressure Vessels JB 4744-2000 钢制压力容器焊接样品机械性能试验(12) Nondestructive Test of Pressure Vessels JB4730-2000 压力容器无损检测(13) Carbon Steel and Low Alloy Steel Forgings for Pressure Vessels JB 4726-2000碳钢及低合金钢锻制压力容器(14) Stainless Steel Forging
12、s for Pressure Vessels JB 4728-2000 不锈钢锻制压力容器(15) Seismic Protection Code for Petrochemical Equipment HG 3048-1996 石化设备地震保护规范1.2.2 Vendor shall be responsible for making all aspects of materials, design, fabrication, inspection and testing conform to the requirements of the specified codes, standard
13、s and local regulations.卖方负责根据指定的规范、标准和地方规章的要求提供材料、设计、制作、检测及试验。Where there are conflicts between the requirements in Purchasers drawings/specifications and the specified codes/standards or local regulations, the order of precedence shall be as follows:如果买方图纸/规范同指定的规范、标准或地方规章之间存在冲突,按以下先后顺序加以遵守:(1) Lo
14、cal regulations 地方规章(2) Engineering drawings 工程图纸(3) Engineering specifications 工程规范(4) Codes and standards 规范和标准In such a case, Vendor shall promptly refer the conflicts to Purchaser in writing to obtaining Purchasers instruction.在此情况下,卖方需及时书面告知买方以获得买方指示。1.3 Units 单位Unless otherwise specified, SI u
15、nits shall be applied as the measurement system for the drawings and documents to be submitted. However, nominal sizes of piping components shall be in accordance with inch system.除非另有规定,图纸及文件中所提及的单位均为国际制。但是,管道部件的公称尺寸应符合英制1.4 Purchasers Drawing and Documents 买方图纸和文件1.4.1 Purchaser will provide Engin
16、eering Drawing for each pressure vessel which contains such information as the shape, basic dimensions, estimated thickness and weight, design conditions, materials for primary parts, nozzle specifications, and details of internals as required by Vendor to accomplish his mechanical design of the pre
17、ssure vessel.买方需根据卖方要求为每台压力容器提供工程图纸说明形状、基本尺寸、估计厚度和重量、设计条件、主部件材质、设备口规格及内件详情,以便完成压力容器的机械设计。When sketches, data sheets or duty specifications are provided, Vendor shall prepare Engineering Drawings covering the same contents as specified above. Such drawings may be used as Vendors assembly drawings wit
18、h necessary information added.在提供了草图、数据表或相关规格后,卖方应绘制包含上述同样内容的工程图纸。这些图纸在加上必要的信息后可用作卖方装配图。1.4.2 Purchaser will provide D-123 “Vessel Standard” which supplements the above drawings and determines the detail construction of pressure vessels.买方将提供D-123“容器标准”作为上述图纸的补充,并决定压力容器的具体施工。When sketches or data sh
19、eets are provided, Vendor shall confirm Purchaser the application of each drawing in Vessel Standard.在提供了草图或数据表后,卖方需根据容器标准对图纸进行确认。1.5 Vendors Drawings and Documents 卖方图纸和文件1.5.1 Vendor shall submit to Purchaser drawings and documents as called for in Purchasers requisition sheets.卖方将根据买方需求单向买方提供图纸和文
20、件。1.5.2 All drawings and documents shall give the name of Client (end user), Purchasers Work No., Item No. and service of the commodity.所有图纸和文件上需给出业主名称(最终用户),买方工程编码、设备位号及系统名称。1.5.3 Drawings shall be prepared to scale and in third angle projection.图纸需按比例使用每三角投影法进行绘制。1.5.4 Drawings shall contain: 图纸需包
21、括:(1) Title block (Purchasers Work No., Requisition No., Item No. and service of the commodity)工程图明细表(买方工程编码、投标邀请号、设备位号及系统)(2) Design Data (conforming to Purchasers drawings or data sheet)设计数据(根据买方图纸或数据表)(3) Material list (material specifications and quantities for all parts including spare parts)材料
22、清单(所有部件、包括备件的材料规格和数量)(4) Nozzle list (conforming to Purchasers drawings or data sheet) 设备口清单(根据买方图纸或数据表)(5) All weld seams, and weld and surface finish symbols 所有焊缝及表面加工符号(6) Detailed dimensions and thickness 详细尺寸及厚度1.5.5 Strength calculations shall cover: 强度计算包括:(1) Code calculations for all pressu
23、re retaining parts including reinforcements for nozzle openings所有压力保持部件,包括设备口加固件的代码计算(2) Structural calculations for internals 内件结构计算(3) Structural calculations for lifting lugs and transportation fittings 吊耳和运输装置的结构计算(4) Stability check of vessel and support for wind/seismic load容器及支架的风力/地震力载荷的稳定检查
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 压力容器 工程 规范 中英文 对照
1、咨信平台为文档C2C交易模式,即用户上传的文档直接被用户下载,收益归上传人(含作者)所有;本站仅是提供信息存储空间和展示预览,仅对用户上传内容的表现方式做保护处理,对上载内容不做任何修改或编辑。所展示的作品文档包括内容和图片全部来源于网络用户和作者上传投稿,我们不确定上传用户享有完全著作权,根据《信息网络传播权保护条例》,如果侵犯了您的版权、权益或隐私,请联系我们,核实后会尽快下架及时删除,并可随时和客服了解处理情况,尊重保护知识产权我们共同努力。
2、文档的总页数、文档格式和文档大小以系统显示为准(内容中显示的页数不一定正确),网站客服只以系统显示的页数、文件格式、文档大小作为仲裁依据,平台无法对文档的真实性、完整性、权威性、准确性、专业性及其观点立场做任何保证或承诺,下载前须认真查看,确认无误后再购买,务必慎重购买;若有违法违纪将进行移交司法处理,若涉侵权平台将进行基本处罚并下架。
3、本站所有内容均由用户上传,付费前请自行鉴别,如您付费,意味着您已接受本站规则且自行承担风险,本站不进行额外附加服务,虚拟产品一经售出概不退款(未进行购买下载可退充值款),文档一经付费(服务费)、不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
4、如你看到网页展示的文档有www.zixin.com.cn水印,是因预览和防盗链等技术需要对页面进行转换压缩成图而已,我们并不对上传的文档进行任何编辑或修改,文档下载后都不会有水印标识(原文档上传前个别存留的除外),下载后原文更清晰;试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓;PPT和DOC文档可被视为“模板”,允许上传人保留章节、目录结构的情况下删减部份的内容;PDF文档不管是原文档转换或图片扫描而得,本站不作要求视为允许,下载前自行私信或留言给上传者【可****】。
5、本文档所展示的图片、画像、字体、音乐的版权可能需版权方额外授权,请谨慎使用;网站提供的党政主题相关内容(国旗、国徽、党徽--等)目的在于配合国家政策宣传,仅限个人学习分享使用,禁止用于任何广告和商用目的。
6、文档遇到问题,请及时私信或留言给本站上传会员【可****】,需本站解决可联系【 微信客服】、【 QQ客服】,若有其他问题请点击或扫码反馈【 服务填表】;文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“【 版权申诉】”(推荐),意见反馈和侵权处理邮箱:1219186828@qq.com;也可以拔打客服电话:4008-655-100;投诉/维权电话:4009-655-100。