正面吊监控解决方案rev.docx

ORLACO-正面吊- 监控系统系统简介：ORLACO 为正面吊旳多种车型提供摄像头-显示屏旳视野处理方案。由于正面吊旳构造设计会对驾驶员导致严重旳视野盲区。良好旳视野处理方案对集装箱旳安全搬运至关重要。下图中灰色点阵区域为经典旳视野盲区。ORLACO 提供 3 个监控视野来辅助驾驶员安全驾驶。- 吊具视野由安装在吊具旳旋锁位置旳 2 个摄像头提供，以 2 分画面显示。- 前方顶部视野由吊具前方顶部位置旳摄像头提供，以全屏画面显示。- 倒车后视视野由安装在尾部旳摄像头提供，以全屏画面显示。ORLACO 产品性能与系统功能：FAMOS 紧凑型摄像头具有高抗震能力，低延时，IP69K 防水等级。并且针对不一样视野提供不一样广角镜头型号。Multiview-DVR 行车记录仪结实紧凑，抗震防水。适合正面吊旳恶劣环境使用。监控系统旳记录时间不不大于 7 天。12 寸显示屏结实抗震，可以按照现场条件自动调整亮度。它提供开关量接口供外部切换信号使用。专用旳视频多芯带屏蔽电缆，可以很好地抗紫外线和油污，抗电磁干扰，为系统旳信号传播保证稳定旳图像质量。画面旳控制切换：当车辆停止或前进时，显示吊具视野。当驾驶员需要观测集装箱旳前方视野时，可以用旋钮开关切换到前方顶部视野。当车辆后退时，显示倒车视野。视野效果请参照下页。安装案例吊具旋锁视野前方顶部视野倒车视野 吊具 21m21m 21m5m 伸缩臂 21m21m 红色：24VDC+ 白色：地线前视画面手动开关倒车档 客户提供部分 3.411m3.411m2.311m显示屏自带电缆6m4.124V电源输入红色：24VDC+ 白色：地线 Cam.13.13.23.3吊具摄像头左MULTIVIEW-DVR 4路行车记录仪Cam.23.13.23.3吊具摄像头右 Cam.3 Front View 2.1 2.2 前视摄像头Cam.41.11.2Rear View后视摄像头显示屏 12寸4.2Cam.2 后视显示屏自带电缆6mCam.3 前视 TITLE:监控系统图CLIENT:xxxxREF:BV17-10xx物料表UPDATE:2023-12-04REVISION:1SUBJECT:正面吊ISSUED FOR:QUOTATIONDRAWN:CHECKED:PAGE:1 NOTE: Vision is our missionCamera FAMOS PAL 20: Article no. 017106040: Article no. 017105060: Article no. 017104080: Article no. 0171030102: Article no. 0171020118: Article no. 0171010129: Article no. 0171000Camera FAMOS NTSC 20: Article no. 017116040: Article no. 017115060: Article no. 017114080: Article no. 0171130102: Article no. 0171120118: Article no. 0171110Dimensions129: Article no. 0171100 2023 DS0171000 R2-119RM6 x 206,5Min. bend radius (R) = 50mmUnits in mmProduct Data55 TECHNICAL DATACamera FAMOS 20/129 PAL/NTSCDescriptionArticle number PAL0171060017105001710400171030017102001710100171000Article number NTSC0171160017115001711400171130017112001711100171100FAMOS 20FAMOS 40FAMOS 60FAMOS 80FAMOS 102FAMOS 118FAMOS 129Lens specified20406080102118129Horizontal lens angle20406080102118129Vertical lens angle15314457738997SensorVideo signalPAL = 720(H)x576(V) 50fld/s. NTSC = 720(H)x480(V) 60fld/s. 1 Vtt composite video into 75 Ohm.Sensor element” CMOS digital image sensor. 640 H x 480 V.Light sensitivity0,05 Lux.Dynamic Range80dB.ElectricalPower input*12.24V/DC.Below 6V: camera is non functional. Between 7V heating element automatically activated (20% capacity). At 8V the camera is fully functional and the heating is at 40% of its capacity. At 12V the heating is at 100% capacity. Between 12V and 33V camera and heating element are fully functional. Above 33V the overvoltage protection is activated and camera plus heating element are switched off. This overvoltage-protection is deactivated below 32V. Powercircuit is protected up to 80V/Dc.Outputs are Short Circuit Protected.In all these above mentioned values; a tolerance of +/-10% is applied.Power consumptionHeating off: 1.1W at 12V, 1.2W at 24V; Heating on: Max. power at 24V 0,15A = 3,6W. Max. power at 12V 0.28A = 3.4W.Inrush currentAt 12V: 4.5A, 300us. At 24V: 12.0A, 300us.Heater element2.4W max.Transient protectionCamera may be powered directly from 12V or 24V battery without additional electrical protection since camera has an integrated circuit that protects the camera against over- and undervoltage, spikes, ripples and loaddumps.Connectors0,5m cable with 4p molded male connector (camera power input and video output).Min. cable bend radius50mm.MechanicalHousingCycoloy (PC + ABS). Filling: Camera is potted with Polyurethane elastomer.Ingress protectionIP68 according to IEC 60529; dust tight and protected against the effects of continuous immersion in water up to 10m under water for 30 minutes. IP69k according to DIN 40050-9: camera can withstand a high pressure cleaning with water: 14-16L/min. 80C and 100 bars flow.Mounting hardwareStandard stainless steel.Shock constancyShock and vibration resistant for usage on trucks, cranes, fork-lifts, maritime applications, machinery. Random vibration test 15,3Grms at frequency: 24 to 2023, PSD (g/Hz) 0,04 to 0,10.Camera bracketMaterial: glass reinforced polyamide, test: 50 Nm at -40C to +85C.Weight0,21kg, 0,29 in standard packing.Truck useWithstand all fluids and materials used in and around trucks like: ammonia solution 5%, ethanol 80-100%, isopropanol5-10%, soapy water (min. 50% soap per volume), alkaline degreasing compounds(used in high pressure washing equipment).Operating temperature-40C to +85C.Storage temperature-40C to +100C.CertificationApprovalsApprovals in compliance with all relevant EMC- and Automotive directives. This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Certificates available upon request.Green PassportAll materials are compliant to Green Passport requirements according IMO resolution MEPC.197(62) as adopted on 15 July 2023 (Maritime sector: International Maritime Organization concerning the functions of the Marine Environment Protection Committee).32Electrical connectionsFront side of molded 4p male connector1 = Coax core= Video signal412 = Coax screen = Video GND3 = Red= 12.24V/DC4 = Black/orange = 0VShieldingTo connector housingAll data subject to change without notice. All dimensions are for commercial purpose only.The camera/display systems from Orlaco comply with the latest CE, ADR, EMC and mirror-directive regulations, where applicable.All products are manufactured in accordance with the ISO 9001 quality management system, ISO/TS 16949 quality automotive, ISO 14001 environmental management systems and all Ex products with the IECEx scheme and ATEX directives, where applicable.Vision is our missionCamera FAMOS 118 PAL IR LEDArticle no. 0171600Camera FAMOS 80 PAL IR LEDArticle no. 0171610Camera FAMOS 118 NTSC IR LEDArticle no. 0171620Camera FAMOS 80 NTSC IR LEDArticle no. 0171630 2023 DS0171600 R1-255L= 500mm19RM6 x 206,5Min. bend radius (R) = 50mmUnits in mmProduct DataDimensions TECHNICAL DATACamera FAMOS 80/118 PAL/NTSC IR LEDDescriptionArticle number0171600017161001716200171630FAMOS 118 PAL IR LEDFAMOS 80 PAL IR LEDFAMOS 118 NTSC IR LEDFAMOS 80 NTSC IR LEDLens specified1188011880Horizontal lens angle1188011880Vertical lens angle89598959SensorVideo signalPAL = 720(H)x576(V) 50fld/s. NTSC = 720(H)x480(V) 60fld/s. 1 Vtt composite video into 75 Ohm.Sensor element” CMOS digital image sensor. 640 H x 480 V.Light sensitivity0,05 Lux.LED4 High Power Infrared LEDs (850nm).Activation IR LEDsModern software algorithm measures automatically the output parameters of the CMOS sensor and automatically decides and activates the value of IR illumination needed for the best image. IR LEDs are activated between 0% and 100% in steps of 1%.ElectricalPower input12.24V/DC.Below 6V: camera is non functional. Between 7V heating element automatically activated (20% capacity). At 8V the camera is fully functional and the heating is at 40% of its capacity. At 12V the heating is at 100% capacity. Between 12V and 33V camera and heating element are fully functional. Above 33V the overvoltage protection is activated and camera plus heating element are switched off. This overvoltage-protection is deactivated below 32V. Powercircuit is protected up to 80V/Dc.Outputs are Short Circuit Protected.In all these above mentioned values; a tolerance of +/-10% is applied.Power consumptionCamera only: 1.2W at 12V , Heater & full LED on: 7,5W at 12V.Camera only: 1.2W at 24V , Heater & full LED on: 7,5W at 24V.Inrush currentAt 12V: 4.5A, 300us. At 24V: 12.0A, 300us.Heater element2.4W max.Transient protectionCamera may be powered directly from 12V or 24V battery without additional electrical protection since camera has an integrated circuit that protects the camera against over- and undervoltage, spikes, ripples and loaddumps.Connectors0,5m cable with 4p molded male connector (camera power input and video output).Min. cable bend radius50mm.MechanicalHousingCycoloy (PC + ABS). Filling: Camera is potted with Polyurethane elastomer.Ingress protectionIP68 according to IEC 60529; dust tight and protected against the effects of continuous immersion in water up to 10m under water for 30 minutes. IP69k according to DIN 40050-9: camera can withstand a high pressure cleaning with water: 14-16L/min. 80C and 100 bars flow.Mounting hardwareStandard stainless steel.Shock constancyShock and vibration resistant for usage on trucks, cranes, fork-lifts, maritime applications, machinery. Random vibration test 15,3Grms at frequency: 24 to 2023, PSD (g/Hz) 0,04 to 0,10.Camera bracketMaterial: glass reinforced polyamide, test: 50 Nm at -40C to +85C.Weight0,21kg, 0,29 in standard packing.Truck useWithstand all fluids and materials used in and around trucks like: ammonia solution 5%, ethanol 80-100%, isopropanol5-10%, soapy water (min. 50% soap per volume), alkaline degreasing compounds(used in high pressure washing equipment).Operating temperature-40C to +85C.Storage temperature-40C to +100C.CertificationApprovalsApprovals in compliance with all relevant EMC- and Automotive directives. This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Certificates available upon request.Green PassportAll materials are compliant to Green Passport requirements according IMO resolution MEPC.197(62) as adopted on 15 July 2023 (Maritime sector: International Maritime Organization concerning the functions of the Marine Environment Protection Committee).Electrical connections32Front side of molded 4p male connector1 = Coax core= Video signal2 = Coax screen = Video GND413 = Red= 12.24V/DC4 = Black/orange = 0VShieldingTo connector housingAll data subject to change without notice. All dimensions are for commercial purpose only.The camera/display systems from Orlaco comply with the latest CE, ADR, EMC and mirror-directive regulations, where applicable.All products are manufactured in accordance with the ISO 9001 quality management system, ISO/TS 16949 quality automotive, ISO 14001 environmental management systems and all Ex products with the IECEx scheme and ATEX directives, where applicable.Vision is our missionCable 1m UNI Article no. 0301960Cable 1,3m UNI Article no. 0301440Cable 2m UNI Article no. 0301870Cable 3m UNI Article no. 0301890Cable 5m UNI Article no. 0301880Cable 7,5m UNI Article no. 0301910Cable 8m UNI Article no. 0301930Cable 9m UNI Article no. 0301950Cable 11m UNI Article no. 0301900Cable16m UNI Article no. 0301920Cable 21m UNI Article no. 0301940Cable 40m UNI Article no. 03019902023 DS0301870 EN R2-1Label 2Cable length LLabel 1Cable Connector Female 4 pinsLabel 1CAMERA-ENDCable Connector Male 4 pinsLabel 20301*KYMXXXXProduct DataDimensions TECHNICAL DATACable *m UNIDescriptionCable length1m1,3m2m3m5m7,5mArticle number030196003014400301870030189003018800301910Cable length8m9m11m16m21m40mArticle number030193003019500301900030192003019400301990Operating temperature-40C to +85CConnectorsCable connector M16 4 pins, molded.ProtectionIP67 according IEC 60529.CableMulticable 1 x coax, 2 x power, 1 x data.JacketBlack, PVCBending radius7,5 mm x diameter (static).Electrical connection1 = Coax core= Video signal232 = Coax shielding= Video GND3 = Red= 12V/DC144 = Black = 0V Shielding = GNDFront sidefemale connector3241Front sidemale connectorAll data subject to change without notice. All dimensions are for commercial purpose only.The camera/display systems from Orlaco comply with the latest CE, ADR, EMC and mirror-directive regulations, where applicable.All products are manufactured in accordance with the ISO 9001 quality management system, ISO/TS 16949 quality automotive, ISO 14001 environmental management systems and all Ex products with the IECEx scheme and ATEX directives, where applicable.Vision is our mission3064,57 (4x)Adjustable bracket298,315,735,470R = 50Cable lenght 6000mmUnits in mmSet Mounting MaterialMin. bend radius= 50mm236,3154,640,5Set Monitor 12” RLED Serial R6Article no. 0411130 2023 DS0411130 EN R2-1Product DataDimensions TECHNICAL DATASet Monitor 12” RLED Serial R6DescriptionSet Artikelnummer0411130MonitorArticle No. 0207910 Monitor 12” RLED SerialCableArticle No. 0304830 Cable Monitor 6 ow b7BracketArticle No. 2023600 Adjustable Bracket 190mmMounting materialArticle No. 0910310 Set Mounting Material Adjustable BracketGeneralWeight2,81 kg, including cable and bracket.TypeAutomotive 12,1inch TFT-LCD module with a white LED backlight.ResolutionXGA 1024 x R.G.B. x 768 pixels.Viewing80 horizontal and 70 vertical ( CR10).LED live time30.000 Hrs.Typical performanceCenter luminance of white: 500cd/m2, Contrast ratio 700:1, Response time 5ms (Tr).SoftwaremenuFull On-Screen-Display (OSD) functionality in 8 languages: English, Dutch, German, French, Italian, Polish, Spanish, Swedish.ABC modeImproved Auto Brightness Control (ABC) including one-touch day/night setting and adjustable minimum and maximum levels for automatic control.Operating temperature