汽车专业毕业设计翻译英文翻译english.doc

Development of Integrated Motor Assist Hybrid System:
Development of the ‘Insight’, a Personal Hybrid Coupe
Kaoru Aoki, Shigetaka Kuroda, Shigemasa Kajiwara,
Hiromitsu Sato and Yoshio Yamamoto
Honda R&D Co.,Ltd.
Copyright ©2000 Society of Automotive Engineers, Inc.

ABSTRACT
This paper presents the technical approach used to design and develop the powerplant for the Honda Insight, a new motor assist hybrid vehicle with an overall development objective of just half the fuel consumption of the current Civic over a wide range of driving conditions. Fuel consumption of 35km/L (Japanese 10-15 mode), and 3.4L/100km (98/69/EC) was realized. To achieve this, a new Integrated Motor Assist (IMA) hybrid power plant system was developed, incorporating many new technologies for packaging and integrating the motor assist system and for improving engine thermal efficiency. This was developed in combination with a new lightweight aluminum body with low aerodynamic resistance. Environmental performance goals also included the simultaneous achievement of low emissions (half the Japanese year 2000 standards, and half the EU2000 standards), high efficiency, and recyclability. Full consideration was also given to key consumer attributes, including crash safety performance, handling, and driving performance.
1. INTRODUCTION
To reduce the automobile’s impact on society and the environment requires that it be increasingly cleaner and more energy efficient. The issues of energy conservation, ambient air quality, and reduction in CO2 emissions are increasing raised as global environmental concerns. One solution for dealing with these issues is the hybrid automobile. Honda has developed and introduced to several major markets worldwide the Insight, a new generation of vehicle design. The Insight combines a hybrid power train with advanced body technology features to meet an overall goal of achieving the highest fuel economy practical.
The hybrid power train is a motor assist parallel configuration, termed IMA for ‘Integrated Motor Assist’. This power train combines a highly efficient electric motor with a new small displacement VTEC engine, a lightweight aluminum body, and improved aerodynamics to realize 3.4L/100km (CO2:80g/km) on 98/69/EC fuel economy. Low emissions performance was also targeted with emission levels achieving the EU2000.
In addition to recapturing deceleration energy, the integrated motor provides high torque assist during typical urban driving accelerations. This allows a significant reduction in engine displacement and higher engine efficiency. Sustained hill climbing performance and high speed cruising capability are assured by a power-toweight ratio of approximately 56kW per metric ton. New engine technology includes the application of a new VTEC (Variable valve Timing and valve lift, Electronic Control) cylinder head design promoting high efficiency and fast catalyst activation, and a new lean NOx catalyst system which promotes lean burn combustion and a reduction in emissions. Extensive friction and weight reducing features are also applied.
2. DEVELOPMENT TARGETS AND CONCEPT
Development was aimed at the achievement of extremely low fuel consumption. We set a target of twice the fuel economy of the current production Civic, Honda’s representative high fuel economy car at 7.0 L/100km (93/116/ EC). As a result, the Insight has the lowest fuel consumption in the world, among gasoline passenger cars.
Exhaust emission performance often tends to be sacrificed for the sake of low fuel consumption. However, we also decided to match the low emissions performance achieved by other mass production cars. Consideration was also given to recyclability (another important environmental issue), crash safety performance, and the basic car characteristics including handling and styling.
Summarizing the above, our development targets were as follows:
· The best fuel consumption performance in the world
· Ultra-low exhaust emissions
· Superior recyclability
· The world's highest level of crash safety performance
· Advanced styling
· Practical features and responsive handling
· Comfortable two-seat configuration with personal utility space
3. POLICIES FOR FUEL CONSUMPTION REDUCTION
In order to establish the technical approach for achieving the fuel consumption target, we conducted a detailed analysis of the energy consumption of the base car, a Civic equipped with a 1.5 liter engine. We found that it was useful to divide the targeted efficiency gains roughly into thirds, as shown in Fig. 1, in order to achieve the low fuel consumption and numerous other above-mentioned goals. These divisions are as follows.
· Improvement of the heat efficiency of the engine itself
· Recovery of braking energy and employment of idle stop using a hybrid power plant
· Car body technologies including reduction of weight and reduced aerodynamic and rolling resistance.

Figure 1. Target of double the fuel economy of CIVIC
Aiming to establish a benchmark for 21st century automobile power trains, we developed this new Integrated Motor Assist power train. This power train simultaneously achieves both extremely low fuel consumption of 3.4L/100km, and low exhaust gas emission performance, befitting a next-generation car.
This paper reports on the newly developed IMA system, including the lean burn engine, electric motor, power control unit, battery technology, and exhaust emission control technology used in the "Honda Insight".
4. AIM OF THE IMA SYSTEM
While developing this next-generation IMA hybrid system, we incorporated as many currently achievable technologies and techniques as possible, in order to achieve the "world's lowest fuel consumption".
The following four system development themes were established in order to meet this target.
1. Recovery of deceleration energy
2. Improvement of the efficiency of the engine
3. Use of idle stop system
4. Reduction of power train size and weight
5. OVERVIEW OF THE IMA SYSTEM
5.1. SYSTEM CONFIGURATION – As shown in Fig. 2, the IMA system uses the engine as the main power source and an electric motor as an auxiliary power source when accelerating. Using a motor as an auxiliary power source simplifies the overall system and makes it possible to use a compact and lightweight motor, battery, and power control unit (PCU).

Figure 2. IMA System
A permanent magnet DC brushless motor is located between the engine and the transmission. When decelerating, the rate of deceleration is calculated for each gear and the PCU controls the motor to generate electricity (recover energy), which charges a nickel-metal hydride battery. When accelerating, the amount of auxiliary power provided (hereafter called "assist") is calculated from the throttle opening, engine parameters, and battery state of charge. The PCU controls the amount of current flowing from the battery to the drive motor
5.2. RECOVERY OF DECELERATION ENERGY – Recovering deceleration energy through regeneration makes it possible to supplement the engine’s output during acceleration and reduce the amount of fuel consumed. Reducing resistance due to running losses, including engine frictional losses, increases the available energy for regeneration. In particular, minimizing the engine displacement is an effective means of reducing friction. Engine displacement reduction also has several other benefits, such as weight reduction and increased thermal efficiency. The IMA system effectively increases the amount of regeneration during deceleration by optimizing the engine and transmission specifications.
5.3. REDUCTION OF ENGINE DISPLACEMENT – Reducing engine displacement is a very important factor in improving fuel economy of a hybrid drive train. However, modern automobiles have to perform over a wide dynamic range. Reducing the displacement is equivalent to lowering the basic performance characteristics of the car. As shown in the output characteristics graph in Fig. 3, the IMA system assists the engine in the low rpm range by utilizing the hightorque performance characteristic of electric motors. The motor can increase overall toruque by over 50% in the lower rpm range used in normal driving. Output in the high rpm range is increased by using a Variable valve Timing and valve lift Electronic Control (VTEC) engine. Thus sufficient peak power is assured and makes it possible to use a new, small displacement 1.0 liter engine.

Figure 3.Engine speed (rpm) Output performance of IMA SYSTEM
Assist from the electric motor while accelerating is a very efficient means of reducing the amount of fuel consumed.
5.4. ACHIEVING LEAN BURN ENGINE OPERATION – Assist from the electric motor, based upon the throttle opening, creates quite linear torque characteristics. This, in turn, improves driveability. In addition, motor assist is also provided under moderate load conditions to broaden the lean-burn operating range, bringing out the full potential of the newly developed lean burn engine.
5.5. IDLE STOP SYSTEM – Stopping the engine rather than idling at stops is also an effective means for reducing fuel consumption. In order to restart the engine with the minimum amount of fuel consumption, the engine is quickly cranked to 600 rpm or more by the hightorque integrated motor before ignition occurs, as shown in Fig. 4. This makes it possible to minimize the amount of fuel consumed, in addition to the fuel saved by not running the engine at idle.
There are many issues to be considered when performing idle stop. These include judging the driver's intent to stop, preparing for the restart, providing a smooth feeling of deceleration, and minimizing vibration of the car body when the engine stops.

Figure 4.Time (sec) The number of cranking in the engine start
This IMA system results in the achievement of both very quick restarts and exceptionally smooth starts.
6. MOTOR ASSIST MECHANISM
6.1. DEVELOPMENT OBJECTIVES – By limiting the IMA motor functions to assistance and regeneration, development themes were established to achieve the following two points.
1. A simple and compact structure
2. A system weight of 10% (80 kg) or less of the completed car weight
6.2. THIN PROFILE DC BRUSHLESS MOTOR – A thin and compact DC brushless motor with engine assist and energy regeneration functions was coupled to the engine crank-shaft (Fig. 5).

Figure 5. Section view of Motor
This is a high efficiency, compact, and lightweight permanent magnet-type three-phase synchronous electric motor with a maximum output of 10 kW. In addition to developing technologies to reduce the weight and increase efficiency, we also aimed to make the motor as thin as possible in order to achieve a compact power train. Lost wax precision casting process was used for the rotor, rotating by bending coupled to the crankshaft. This achieves high strength and lighter weight (approximately -20%) compared with normal cast products. For the rotor magnets, further improvements were made to the neodymium-sintered magnets used in the HONDA EV PLUS, realizing approximately 8% greater torque density and improved heat resistance. This design also results in a motor structure that does not require a cooling system. A split stator structure with salient pole centralized windings was developed and used to reduce the motor axial width. A split stator was adopted to drive the rotor. This makes it possible to use the salient pole centralized windings, which are both more compact and efficient than the conventional coil wave winding method, as shown in Fig. 6. In addition, centralized distribution bus rings (Fig. 7) formed from copper sheets were used for the harness that supplies electricity to the coils on both sides of the stator. This results in an extremely compact and simple structure. These improvements achieve an extremely thin motor with a width of only 60 mm. This represents a 40% reduction in width compared to conventional technology.

Wave winding Salient pole winding
Figure 6. Compare of winding

Figure 7. Cut view of Motor
6.3. NICKEL-METAL HYDRIDE (NI-MH) BATTERY – A nickel-metal hydride battery is used to store and provide electrical energy for the motor assist. This is an advanced battery which has already achieved proven results in the high specific energy version used for the HONDA EV PLUS electric vehicle. The hybrid vehicle battery features stable output characteristics, regardless of the state-of-charge status. It is also extremely durable in this application. The battery pack has an integrated structure consisting of 20 modules, each having six
D-size cells connected in series, arranged in a lattice formation. These 120 1.2 V cells are all connected in series for a total battery pack voltage of 144 V.
6.4. POWER CONTROL UNIT (PCU) – The PCU performs precise control of motor assist/regeneration and supplies power to the 12 V power source. It has built-in cooling functions, which give it a lightweight, efficient and compact structure. Significant weight reduction was achieved by integrating an air cooling system using highly efficient cooling fins and a magnesium heat sink case.
The inverter for the drive motor, which is the most important component within the PCU, has switching elements integrated into a single module for generating the three-phase AC current. These were separate components on the EV PLUS. The drive circuit has been miniaturized and converted to an IC using high density integration. These improvements have resulted not only in significant weight reduction, but have also improved the power conversion efficiency. Further, using phase control to drive the motor at very high efficiencies reduces the amount of heat produced and makes it possible to use a lightweight and simple air-cooling system. (Fig. 8)
Figure 8.Inverter Cut view of PCU Heat Sink case
7. ENGINE
7.1. DEVELOPMENT OBJECTIVES – The following four points were set as development themes in order to achieve low fuel consumption over a wide range of operating conditions.
1. Improvement of thermal efficiency
2. Reduction of mechanical losses (-10% compared with conventional designs )
3. Reduction of size and weight (lightest weight in its class)
4. Achievement of half the EU2000 standards
7.2. ENGINE OVERVIEW AND SPECIFICATIONS – The engine specifications are shown in Table 1 and the main new features and their purposes are shown in Table 2.

First, a displacement of approximately 1000 cm3 was considered optimal for this vehicle with the IMA system, so a 3-cylinder engine was selected to minimize combustion chamber surface-to-volume ratio and mechanical losses. (Fig. 9)
7.3. FUEL CONSUMPTION – Engine displacement could be reduce considerably in the motor assist powertrain because of the motor assist enhancement of low rpm torque, and also VTEC for sufficient peak power output from the engine. A key feature