EMCVPLEX安装实施专项方案.docx

VPLEX-LOCAL硬件配置信息此次安装VPLEX-Local有单台台VPLEX组成，VPLEX硬件配置以下：1) 1个Engine2) 2个Director，每个Engine由两个Director组成3) 8个8Gb前端FC端口，每个Director包含一块前端FC卡，共4个8Gb前端FC端口，因为交换机端口限制，此次使用4个前端FC端口（每个Directo上两个）。4) 8个8Gb后端FC端口，每个Director包含一块后端FC卡，共4个8Gb后端FC端口。此次使用4个前端FC端口（每个Directo上两个）5) 4个可用8GbVPLEX-Local级联FC端口，每个Director包含一块VPLEX-Local级联FC卡，共4个8Gb级联FC端口，不过只有两个可用VPLEX-LOCAL硬件介绍单台VPLEX硬件布局VPLEXENGINE硬件布局VPLEX-LOCAL级联端口连接VPLEX-LOCAL拓扑结构VPLEX-LOCALFABRIC拓扑图VPLEX-LOCAL后端存放系统配置META VOLUME配置请注意每台VNX必需使用两个RG，每个RG各提供两个80G LUN。Mirror和backupmeta volume LUN需分开RG存放。不推荐mirror 和 backup 放在同一个RG里。ClusterMeta VolumeStorageRAID GroupLUN IDRAIDSizeVPLEX_01Meta_Mirror_1VNX5400RG1800RAID1080GBMeta_Bcakup_1VNX5400RG1801RAID1080GBMeta_Mirror_2VNX5400RG0800RAID1080GBMeta_Backup_2VNX5400RG0801RAID1080GBLOGGING VOLUME配置ClusterLog VolumeStorageRAID GroupLUN IDRAIDSizeVPLEX_01Loggin_Mirror_1VNX5400802RAID1010GBMirror 2VNX5400802RAID1010GBVPLEX-LOCAL安装配置步骤VPLEX-LOCAL安装配置具体步骤在VPLEX-Local安装配置过程中，有些命令在Manager Server上运行，有些命令在VPLEX上运行，以下标志代表命令运行场所：【MS_CLUSTER_1】: VPLEX_01Manager Servershell环境下运行【VPLEXCLI_CLUSTER_1】: VPLEX_01VPlexCLI环境下运行，在Manager Servershell环境下，运行“vplexcli”命令进入该环境【MS_CLUSTER_2】: VPLEX_02Manager Servershell环境下运行【VPLEXCLI_CLUSTER_2】: VPLEX_02VPlexCLI环境下运行，在Manager Servershell环境下，运行“vplexcli”命令进入该环境CLUSTER_1安装配置CLUSTER_1初始化配置1. 将配置用笔记本电脑网卡设置为经过DHCP获取IP2. 配置用笔记本电脑经过网线连接到VPLEX_01Manager Servereth1网口3. 经过putty.exe或SecureCRT软件登陆到VPLEX_01Manager Server上，Host IP：128.221.252.2，Connect type：SSH，用户名：service，密码：MiDim7T 4. 设置Manager Server主机名【MS_CLUSTER_1】# sudo /opt/emc/VPlex/tools/ipconfig/changehostname.py -n VPLEX-015. 重新登陆Manager Server，查看提醒符或/etc/HOSTNAME文件内容，确定主机名更改成功【MS_CLUSTER_1】# cat /etc/HOSTNAME6. 运行vplexcli命令登陆到VPLEX_01，用户名为service，密码为MiDim7T【MS_CLUSTER_1】# vplexcli7. 配置Manager Server管理公用IP地址【VPLEXCLI_CLUSTER_1】# management-server set-ip -i VPLEX_01_IP:VPLEX_NETMASK -g VPLEX_GATEWAY eth3【VPLEXCLI_CLUSTER_1】# ll /management-server/ports/eth38. 运行exit命令，退出VPLEX_01到Manager Server，检验公用管理网络连通性【VPLEXCLI_CLUSTER_1】# exit【MS_CLUSTER_1】# ping VPLEX_GATEWAY9. 配置NTP时钟服务器，同时时间【MS_CLUSTER_1】# vi /etc/ntp.conf; 设置外部server为NTP_IP【MS_CLUSTER_1】# sudo /etc/init.d/ntp restart【MS_CLUSTER_1】# date10. 运行exit命令，退出VPLEX_01Manager Server【MS_CLUSTER_1】# exit开启CLUSTER_1DIRECTOR，检验和确定版本信息11. 经过putty.exe或SecureCRT软件登陆到VPLEX_01Manager Server上，用户名为service，密码为MiDim7T12. 运行vplexcli命令登陆到VPLEX_01，用户名为service，密码为MiDim7T【MS_CLUSTER_1】# vplexcli13. 开启VPLEXDirector，确定显示director数量正确（2个director）【VPLEXCLI_CLUSTER_1】# configuration connect-local-directors【VPLEXCLI_CLUSTER_1】# ll /engines/*/directors14. 检验VPLEX及每个Director版本，确定符合版本控制要求【VPLEXCLI_CLUSTER_1】# version【VPLEXCLI_CLUSTER_1】# exit检验硬件运行状态15. 检验VPLEX及每个Director版本，确定符合版本控制要求【MS_CLUSTER_1】VPlexPlatformHealthCheck确定检验结果符合下表：运行EZ-SETUP配置向导16. 运行EZ-Setup配置向导，完成以下方面配置：【MS_CLUSTER_1】# vplexcli【VPLEXCLI_CLUSTER_1】# configuration system-setup提醒选择What would you like to configure? 1. Configure a VPLEX Local (single cluster). 2. Configure a VPLEX Metro (synchronous, 2 clusters). 3. Configure a VPLEX Geo (asynchronous, 2 clusters).Select your configuration choice. (1-3)2What would you like to configure? 1. Configure the first or only cluster. 2. Configure the second cluster of a VPLEX Metro implementation.Select your configuration choice. (1,2)1Are you sure you want to configure the first or only cluster? (yes/no):yesWould you like to configure the login banner? (yes/no):noWould you like to configure an authentication service provider to authenticate VPLEX users? (yes/no) no:noWould you like to configure this cluster to send event notifications to EMC? (yes/no) yes:noWould you like to configure this cluster to send system reports to EMC? (yes/no) yes:noWould you like to configure the cluster to run the SNMP Agent Service? (yes/no) no:noHow many years should the CA certificate remain valid before expiring? EMC recommends 5 years (maximum is 5 years). 5:5How many years should the host certificate remain valid before expiring? EMC recommends 2 years (maximum is 2 years). 2:2Would you like to run the setup process now? (yes/no):yesPlease create a passphrase (at least 8 characters) for the Certificate Authority Key. Make a note of this passphrase as you will need it to configure a second cluster of a VPLEX Metro or Geo. Certificate Authority passphrase:guizhou_sfdxRe-enter the passphrase for the Certificate Authority Key:guizhou_sfdxPlease create a passphrase (at least 8 characters) for the Local Host Certificate Key. Make a note of this passphrase as you will need it later. Host Certificate passphrase:guizhou_sfdxRe-enter the passphrase for the Certificate Key:guizhou_sfdx配置CLUSTER_1和后端存放系统之间ZONE17. 获取VPLEX_01端口WWN【VPLEXCLI_CLUSTER_1】# ll /engines/*/ports18. 登陆到SAN Switch，运行“switchshow”命令，检验VPLEX_01后端端口在SAN Switch上连接是否符合计划，不然依据计划进行调整19. 登陆到SAN Switch，创建和Metadata Volume和Logging Volume相关VPLEX_01后端端口和后端存放系统前端端口之间zoneVPLEX注册到后端存放系统及磁盘分配VPLEX_01后端端口注册到VNXVPLEX_01后端端口在VNX上注册配置提议以下： Host name: VPLEX_01 Host IP: VPLEX_01_IP Initiator type: CLARiiON Open Failover Mode: 4VNX上创建STORAGE GROUP Storage Group: SG_ VPLEX_01 Host: VPLEX_01_1 LUN: 2个78GBMetadata Volume（800、801）和一个10GBLogging Volume（802），和其它数据LUN识别后端存放系统METADATA VOLUME和LOGGING VOLUME20. 识别后端存放系统和对应磁盘设备【VPLEXCLI_CLUSTER_1】# configuration continue-system-setup创建METADATA VOLUME21. 获取适合创建Metadata Volume磁盘设备，比较VPLEXVPD名字和VNX LUNVPD名字，确定VNX5400LUN 800VPD名字和VNX5400LUN 800VPD名字【VPLEXCLI_CLUSTER_1】# configuration show-meta-volume-candidates22. 创建Metadata Volume【VPLEXCLI_CLUSTER_1】# meta-volume create -n VPLEX_01_META -d ,23. 查看Metadata Volume状态，确定active属性列显示为true【VPLEXCLI_CLUSTER_1】# ll /clusters/cluster-1/system-volumes/ VPLEX_01_META24. 查看cluster状态，确定cluster status和operational-status显示为ok【VPLEXCLI_CLUSTER_1】# cluster status设置METADATA VOLUME备份时间25. 获取适合创建Metadata Volume Backup磁盘设备，比较VPLEXVPD名字和VNX LUNVPD名字，确定VNX5400LUN 801VPD名字和VNX5400LUN 801VPD名字【VPLEXCLI_CLUSTER_1】# ll /clusters/cluster-1/storage-elements/storage-volumes26. 选择Metadata Volume备份设备为：VNX5400LUN 801VPD名字,。设置Metadata Volume备份时间（当地时间23:40，UTC时间应该是15:40），开启初始化备份，Metadata Volume备份时间大约为10分钟。【VPLEXCLI_CLUSTER_1】# configuration metadata-backup【VPLEXCLI_CLUSTER_1】# ll /clusters/cluster-1/storage-elements/storage-volumes设置产品注册信息27. 设置产品注册信息，经过邮件发送给EMC【VPLEXCLI_CLUSTER_1】# configuration register-product提醒输入Company Site ID Number (Optional)Company NameContact First NameContact Last NameContact Email AddressContact Phone NumberCompany Street AddressCompany CityCompany State or ProvinceCompany Zip or Postal CodeCompany CountryChinaWhich method will be used to send Event Notifications? Enter the number associated with your selection. 1: ESRS 2: Email 3: None (Event Notifications are not configured) Event Notifications using :3Which method will be used for Remote Support? Enter the number associated with your selection. 1: ESRS 2: WebEx Remote Support using :2Would you like to continue with these values? (Y/N):YTo complete the registration process, this information must be sent to EMC. The product registration information can be sent to EMC for you using an SMTP server of your choice. Would you like to send this now? (Y/N):N完成CLUSTER_1EZ-SETUP安装配置28. 经过putty.exe或SecureCRT软件登陆到VPLEX_01Manager Server上，用户名为service，密码为MiDim7T29. 运行vplexcli命令登陆到VPLEX_01，用户名为service，密码为MiDim7T【MS_CLUSTER_1】# vplexcli【VPLEXCLI_CLUSTER_1】# configuration complete-system-setup